内环境温度也是影响打胶机效果的原因之一

发布时间:2017/10/16    发布人:

1•●、双组份打胶机B胶桶内如果要有空气░,空气将排不出来░,B泵将快速往返运动░,不能向高压泵内正常供胶░,影响整个系统░,因此░,必须将空气排出来。方法是:将压盘提出从新压入并放气。

  1, B glue bucket if there is air, the air will not drain out, B pump will quickly move back and forth, can not give normal glue to the high-pressure pump, affect the whole system, therefore, must exhaust the air. The method is to press the pressure plate from the new into the air.

  2•●、液压站系统的压力░,不能调的太高░,要根据室内环境温度等实际情况░,调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪░,否则B组份管路压力将升得很高░,造成安全事故。

  2, the hydraulic station system pressure can not be adjusted too high, according to the indoor environment temperature and other actual situation, adjust to meet the glue mouth normal glue out, even glue. When the hydraulic station is opened, the glue gun must be opened, otherwise the pressure of the B component pipeline will rise very high, which will lead to a safety accident.

  3•●、定期检查气源░,首先应保证使用经干燥的洁净压缩空气░,并定期排放分离过滤器中的积水░,检查油雾器中的油是否够用。

  3, regularly check the gas source, first of all should ensure the use of dry clean compressed air, and regularly discharge separation filter in the water, check the oil in the fog is enough.

  4•●、若涂胶工作过程中停顿时间超过15分钟以上时░,一定要用“冲枪”。本机有报警功能░,到时没有冲胶会有蜂鸣器报警。

  4, if the glue working process pause time more than 15 minutes, must use "punch gun"". This machine has the alarm function, when there is no glue, there will be buzzer alarm.

  5•●、正常工作时不要断气源░,如果发现断气源应停止工作。

  Don't cut off the gas source, 5 normal work, if it is found that asgassource should stop working.

  6•●、A胶提胶泵连续工作1分钟以上没有供胶停止░,说明管路内有空气░,此时会报警░,须打开泵上管接头再打开A胶提胶泵░,直到出胶为止░,停止并接好接头░,胶枪会出现有空气的哔哔爆破声░,空气排净就好了。

双组份打胶机生产厂家

  6, A glue gel extraction pump work for more than 1 minutes without glue stop, that air is in the pipeline, the alarm will have to open the pump pipe joint, then open the A glue rubber glue pump, until now, stop and connect the connector glue gun will appear beep sound blasting with air. The air net is good.

  7•●、压盘上的放气阀门要保持通畅░,要定期疏通和清洗。

  7, the pressure relief valve on the pressure plate to maintain patency, regular dredging and cleaning.

  8•●、由于每次冲洗混合器不会完全干净░,每次都有少量的混合胶沉积░,越来越多░,以致堵塞混合器通道░,用一段时间后░,影响出胶量和混合效果░,因此要定期(聚硫胶五天░,硅酮胶两天)清洗混合器。把混合器内的混胶棒拆出░,如有损坏更换新的混胶棒。若混胶棒拆不出来░,可用火烧掉░,注意不能损伤零件螺纹。

  8, because every flush mixer will not completely clean, every time there is a small amount of glue mixed deposits, more and more, that blocking the channel mixer, after a period of time, influence the quantity of cement and mixing effect, so regular (five days of polysulfide rubber, silicone rubber mixer cleaning for two days). The glue mixer and mixing, the damage as the replacement of the rubber mixing rod. If the glue stick can not be removed, it can be burnt out, pay attention to not damage the parts thread.

  9•●、硅酮胶B 组份遇空气会结壳░,影响泵的正常工作和管路的畅通░,因此░,停机时B组份胶的所有通道在泄压后均应关闭░,使B组份不得接触空气。

  9, silicone rubber B components in the air will be crusts, affecting the normal operation of the pump and the smooth flow of the pipeline, therefore, downtime, all B components of the channel should be closed after the pressure relief, so that B components shall not touch the air.

  本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站:/谢谢您的到来!

  The wonderful content of this article comes from the two component dispenser, please click on our official website: /, thank you for coming!

www.kecimusic.com
友情链接:68彩票网  诺亚彩票  k8彩票  胜通彩票  波音彩票  传奇彩票  868彩票  爱米彩  龙猫彩票  金福彩票  彩票33  688彩票  金洋彩票  800万彩票  彩83彩票  壹玖玖彩票  宝博彩票  彩34彩票  k8彩票  顺盈彩票