双组份打胶机出现连续花胶四要素

发布时间:2017/09/05    发布人:

  结构胶混合不均匀░,双组份打胶机局部会出现白色条纹。在光线比较亮的情况下░,更加容易观察。混合不均匀和混合均匀的情况░,如下图:结构胶混合不均匀░,会出现什么问题呢?结构胶固化后的强度下降░,固化交联不完全•●、严重时候会发粘░,无法固化等。

  Uneven mixing of structural adhesive, white tape will appear in the two part gluing machine. It's easier to see when the light is brighter. The uneven mixing and mixing evenly, figure: structural adhesive is not mixed evenly, what will happen? Decreased structural adhesive strength after curing, curing incomplete, serious when will be sticky, not curing.

  双组分硅酮结构胶是由主剂A组分(白胶)和固化剂B组分(黑胶)组成░,通过双组分打胶机░,按厂家推荐的比例混合均匀后使用。混合后的结构胶经过一段时间固化░,最终获得好的粘接性能和物理性能。但是░,如果结构胶混合不均匀后使用░,结构胶固化就会出现质量问题。

  The two-component silicone rubber structure is composed of main agent A component (glue) and curing agent B component (black glue), glue machine by two components, according to the manufacturer's recommended mixing ratio after use. The structural adhesive after mixing has been cured for a period of time and finally obtained good adhesion and physical properties. However, if the structural adhesive mixture is not uniform, the structural adhesive will be cured and quality problems will arise.

  混合不均匀的结构胶有以下四种情况及原因如下:

  Mix uneven structural adhesive in the following four situations and the reasons are as follows:

 •●、倭ń海阂话闶腔旌掀鞫氯•●、混合器装配错误或者使用的混合单元不够多;

  It is continuous: General mixer block, mixing unit assembly error or use enough;

 •●、诙闲泄媛苫ń海河胂低承怨收嫌泄░,如配比泵密封泄漏或者比例架磨损;

双组份打胶机价格

  The law relating to it: intermittent system fault, such as the ratio of pump seal leakage or shelf wear ratio;

 •●、鄱闲薰媛苫ń海河牍收嫌泄░,如过滤器堵塞/针阀堵塞/压盘故障/配比泵入口堵塞或者密封失效/安全阀及高压球阀失效等;

  The intermittent of it: and the fault, such as filter clogging / needle clogging / trouble / pressure plate proportioning pump entrance blocked or seal failure / safety valve and high pressure ball valve failure;

 •●、芏淘萃G购笥挚故░,开头出现一段花胶:主要是胶粘度匹配不理想░,需要调整系统管道或降低工作压力。

  The gun and shot after a brief stop at the beginning, it is mainly a: viscosity, not ideal, need to adjust or reduce work pressure pipeline system.

  上述出现花胶的四种情况都是通过排除打胶机故障来解决。

  The above four cases appeared it are solved by gluing machine fault elimination.

  打胶机要定期进行保养░,确保打胶机可以正常工作。每次开机前必须做蝴蝶试验░,确保结构胶混合均匀。

  Make sure the glue machine can work properly. Butterfly test must be done before each turn on to ensure that the structure is well blended.

  蝴蝶试验的方法如下:将打胶机打出的混合好的胶挤到纸中间5-10克░,折合纸将胶压平。打开纸检查胶样░,混合均匀的胶应无异色条纹░,如果胶出现异色条纹░,则表明混胶不均匀░,应查找原因░,问题解决后才能使用。

  Butterfly test methods are as follows: will play the machine to play a good mix of glue squeezed to the middle of the paper 5-10 grams, folded paper will glue flat. Open the paper, check the glue sample, and mix the glue evenly. There should be no color stripes. If the glue appears in different stripes, it shows that the mixture is not uniform. The reason should be found and the problem can be solved.

  本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站: /谢谢您的到来!

  The exciting content of this article comes from the two component dispenser, please click on our official website: /, thank you for coming!

www.kecimusic.com
友情链接:胜通彩票  威尼斯人彩票  七星彩票  好运彩票  乐享彩票  68彩票网  多宝彩票网  现金彩票  777彩票  kk彩票  福中彩票  鸿禾彩票  彩83彩票  博金冠彩票  87彩店  933彩票  七星彩票  人人发彩票  800万彩票  彩拾彩票