提高打胶机工作效率的相关操作

发布时间:2018/04/23    发布人:

  因双组份胶是由两种胶混合而成的░,其凝固速度与环境温度和A•●、B胶的比例有关░,混合后的胶一般在20分钟之内就会反应固化。所以░,当设备在正常打胶后░,20分钟之内不使用就必须将混合后的胶冲洗出来░,以免堵塞混胶器和胶枪。具体操作:将B泵关闭░,打开B胶回流开关然后打开胶枪░,至胶条为白色即可。

  Because the double component glue is made from two kinds of glue, the solidification rate is related to the ambient temperature and the proportion of A and B glue. The adhesive after mixing is generally cured in 20 minutes. Therefore, when the equipment is normally glued, it is necessary to rinse the mixed rubber after 20 minutes without use, so as not to jam the glue mixer and glue gun. Specific operation: turn off the B pump, open the B rubber reflux switch and turn on the glue gun, then the adhesive strip will be white.

  1)松开比例杠杆上的比例泵锁紧螺钉░,将比例泵内外调整至所需比例。只有当A胶和B胶的配比达到正常值时░,才可进行下面的操作。

  1) release the proportional screw on the proportional lever and adjust the proportion of the pump inside and outside to the required ratio. Only when the ratio of A glue and B glue reaches the normal value can the following operation be carried out.

  2)置选择旋钮于A•●、B泵开░,将胶枪出口对准两片玻璃的中缝░,打开胶枪开关░,以适当速度平稳地移动胶枪使玻璃槽内的双组份胶填满充实为佳。打胶结束时关闭胶枪。

双组份打胶机

  2) put the selection knob on the A and B pump, aim the exit of the glue gun at the middle seam of the two glass, open the glue gun switch, and move the glue gun at the proper speed to fill the double component in the glass groove. Turn off the glue gun at the end of the glue.

  5•●、更换胶桶:

  5, replace the glue bucket:

  1)当胶桶内的胶用完时░,应立即关闭A•●、B开关░,停止打胶。

  1) when the glue in the plastic bucket is used up, A and B switches should be closed imtely.

  2)打开A(或B)胶泵充气开关░,选择A(或B)胶泵提升机构为上升位置░,点动旋钮使压盘慢慢提起░,此时应注意:胶桶尽量不要离开底盘░,直至压盘完全脱离胶桶时关闭A(或B)胶泵的充气开关。3)撤出空桶░,将新胶桶置于工作位置░,重复第3•●、4•●、项操作。

  2) open A (or B) glue pump inflatable switch, select A (or B) glue pump lifting mechanism to rise position, point move knob to lift the plate slowly, at this time should pay attention to: glue barrel do not leave the chassis as far as possible, until the press disc is completely out of glue barrel to close the inflatable switch of A (or B) glue pump. 3) withdraw empty barrels, place the new plastic bucket in the working position, repeat the third, fourth item operation.

  本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站:谢谢您的到来!

  The highlights of this article are from two groups of glue dispenser. Please click on our official website: thank you for coming.

www.kecimusic.com
友情链接:彩29彩票  佳运彩票  58彩票  k8彩票  亚博彩票  国民彩票  豪客彩  顺盈彩票  703彩票  博金冠彩票  天际彩票  MY310爱投彩票  666彩票  彩票77  爱拼彩票  亦博彩票  七七彩票  彩世界彩票  361彩票  福中彩票