卧式对双组份打胶机车间环境的限定

发布时间:2017/11/07    发布人:

  纵然是专业人士░,对于打胶机的了解░,双组份打胶机实际上还只是停留在它的实际用途上。不过░,对于打胶机的理解░,停留在它的使用层面已经很难得了。那么░,卧式打胶机究竟对车间厂房的环境有什么要求呢?

  Even for professionals, the two - component punch actually stays in its actual use. However, it is difficult to understand the glue machine at its level of use. So, what are the requirements for the workshop environment of the horizontal sizing machine?

  打胶机对于地面平整度的要求░,这个也是近期我厂参加国际玻璃展览会是被问道最多的问题。小型卧式打胶机对于地面的平整度要求不是非常高░,设备在当初研发阶段我们的工程师已经考虑到地面平整度的问题了所以在研发的过程中也着重的解决这个问题。

  The requirement of the ground roughness of the glue machine, which is the most frequently asked question of our factory's participation in the Beijing international glass exhibition in the near future. Small horizontal gluing machine for surface roughness requirements are not very high, in the initial stage of our equipment R & D engineers have taken into account the flatness of the ground problem so solving this problem is the focus in the process of research and development.

双组份打胶机价格

  我们在设备当中专门增加了一个特殊装置来解决地面不平整对打胶机打胶的影响。当然小编这也要强调一下虽然设备对地面的平整度要求不高░,但是也不能满地是坑坑洼洼的。

  We have added a special device in the equipment to solve the impact of the ground roughness on the gluing machine. Of course this small would like to emphasize that although smooth equipment on the ground of requirements is not high, but not everywhere is bumpy.

  首先我们先说说对场地面积的要求░,卧式打胶机不同于立式打胶机。立式打胶机对于厂房面积的要求比较高保守估计也要尽50平米的地方。而小型打胶机对于厂房面积的要求就要小很多了░,仅仅需要不足10平米的地方就可以存放░,最主要的是由于设备体积小可以任意摆放░,不需要专门为打胶机腾出空间来存放。

  First of all, let's talk about the requirements of the site area, horizontal gum machine is different from the vertical rubber machine. Vertical glue machine for the factory area requirements are relatively high, conservative estimate also need to do 50 square meters of place. Small glue machine for plant area requirements will be much smaller, only less than 10 square meters of the place can be stored, the main equipment is due to small size can be arbitrarily placed, do not need to make room for gluing machine.

  然后我们说下打胶机对于厂房温度•●、湿度的要求░,作为设备来讲打胶机本身对于厂房的温度要求不高░,一般应安装在干燥•●、无粉尘•●、无腐蚀性气体,温度在0~40度的车间内。同其他设备的要求几乎没有什么太大的区别。

  Then we say glue machine for workshop temperature and humidity requirements, as the equipment in terms of atx-ii itself for the workshop temperature is not high, the general should be installed in a dry, no dust, no corrosive gas, temperature 0 ~ 40 degrees in the workshop. There is little difference between the requirements of other equipment.

  本文由双组份打胶机为您提供░,我们的网站是:我们将以全心全意的热情为您提供更优质的服务░,欢迎您的访问!

  In this paper, a two component glue machine to provide you, our website is: , we will wholeheartedly provide you with better service, you are welcome to visit!

www.kecimusic.com
友情链接:703彩票  kk彩票  人人发彩票  彩83彩票  开门彩  YY彩票  博乐彩票  盈宝彩  520彩票  彩29彩票  正点彩票  天际彩票  多多彩票  928彩票  博金冠彩票  博冠彩票  66彩票网  6538彩票  58彩票网  信发彩票