清洗双组份打胶机混合器管道的技巧

发布时间:2017/09/07    发布人:

  1•●、固化速度太快或太慢

  1, curing speed is too fast or too slow

  2•●、双组份打胶机混合不匀░,出现白丝░,花胶

  2, two-component glue mixing is not uniform, white silk, fish maw

 •●、俅蚪夯旌掀鞯ハ蚍孤░,更换单向阀。

  Rubber mixer, mixer one-way valve leakage, replace one-way valve.

 •●、诖蚪夯旌掀骷扒鼓谕ǖ啦糠侄氯░,清洗混合器和管道。

  The glue mixer, mixer and gun passages are blocked, and the mixer and pipe are cleaned.

 •●、鄞蚪夯壤媚谟性辔░,清洗比例泵。

  There is dirt in proportion pump and cleaning proportion pump.

 •●、芸昭够掌沽Σ蛔░,气量不稳░,调整压力。

  The air pressure of the air compressor is not enough, the air volume is unstable, and the pressure is adjusted.

  3•●、打胶机压盘冒胶

  3, glue machine, pressure plate gel

 •●、傺古堂芊馊λ鸹当湫░,老化发硬░,更换新的胶圈。

  The sealing ring of pressure plate is damaged, deformed, aged and hard to be replaced, and new rubber ring is replaced.

 •●、谏笛沽μ。

  The lifting pressure is too great.

双组份打胶机价格

 •●、弁疤罅░,不合适░,客户在采购时░,先量一下自己的打胶机压盘大小░,现在市面上机器压盘有三个规格的░,560mm░,565mm░,571mm,暖万佳科技开发有限公司可以跟据客户的机器压盘大小░,提供相应的包装桶包装。

  The barrel is too big, not appropriate, customers in the procurement, the first volume of your gum machine platen size, now on the market of machine platen three specifications, 560mm, 565mm, 571mm, warm Wanjia science and technology development limited company can according to customer's machine platen size, provide the corresponding packaging barrels packaging.

  4•●、中空玻璃安装░,经冷•●、热交换起雾的问题

  4, the installation of insulating glass, cold and heat exchange fog

 •●、偎榉莨柰褐饕嵌烂芊░,粘结结构的作用░,所以头道密封必须用丁基密封胶密封░,插角处用丁基胶密封完全。

  The two-component silicone rubber is mainly two sealing, bonding structure, so the seal must be sealed with butyl sealant, inserted at the corner completely sealed with butyl rubber.

 •●、诟呶•●、高湿季节░,必须用质量较好的分子筛░,完全能够将玻璃密封后残存的湿气吸干净░,以绝后患。整个操作时间不能太久。

  In the season of high temperature and high humidity, must use the better quality of the molecular sieve can be completely sealed after the remaining moisture glass suction clean, with all. The whole operation shouldn't take long.

  5•●、胶盘压不下去

  5, rubber disc pressure can not go down

 •●、偻氨湫░,不圆了░,可用锤子把桶口拷圆░,再压下去。

  The barrel deion, not round, available hammer bungholes copy circle, press down.

 •●、谕疤×░,或是压盘密封圈过大░,可以在密封圈上涂抹一点白胶░,可起到润滑的作用再压下去。

  The barrel is too small, or the pressure plate sealing ring is too large, you can smear a little glue on the sealing ring, can play the role of lubrication pressure.

  6•●、气泡问题(A组份有气泡或是混合后出现气泡)

  6, bubble problem (A group has bubbles or bubbles after mixing)

 •●、傺菇菏蔽茨芡耆啪】掌░,所以每次换胶时░,一定要把排空气的阀门打开░,等空气排完后再关上。

  Pressure glue can not completely exhaust the air, so every time you change glue, you must open the exhaust valve, and then close the air after the completion of the switch.

 •●、谑侄旖汗讨谢烊肟掌。

  Mixing air in manual mixing process.

  本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站:/谢谢您的到来!

  The exciting content of this article comes from the two component dispenser, please click on our official website: /, thank you for coming!

www.kecimusic.com
友情链接:美娱彩票  彩34彩票  美娱彩票  平安彩票  天鸿彩票  3号彩票  MY310爱投彩票  666彩票  五百万彩票  彩拾彩票  4u彩票  917彩票  66彩票网  博冠彩票  人人发彩票  博金冠彩票  平安彩票  大运彩票  e博彩票  彩票宝