全自动封胶机常见问题及调试方法!

发布时间:2019/05/22    发布人:

很多人在买完设备之后░,就认为说明书没用了。随手一扔░,不知所踪?悸堑胶芏嗳硕伎赡芑嵴庋░,今天全自动封胶机小编就特地给大家总结下中空玻璃全自动封胶机的小问题以及解决办法░,有需要的小伙伴们可以收藏起来呦。
Many people think the instructions are useless after they have bought the equipment. Just throw it away and you don't know where it is. Considering that many people may be like this, today's small edition of automatic sealant machine specially summarizes the small problems and solutions of hollow glass automatic sealant machine, and small partners in need can collect it.
中空玻璃自动打胶机自身带着自我保护功能░,主要针对于停电自我保护。这就意味着░,如果在工作过程中░,突然停电的话░,它会自动关机。即使在来电░,它也不会在自动启动。这时候就需要我们自己将旋钮拨回停位░,在拨回开位就可以启动了。这个可以注意一下。
Hollow glass automatic gluing machine itself has self-protection function, mainly aimed at power failure self-protection. This means that if there is a sudden power failure during the working process, it will shut down automatically. Even when a call comes, it doesn't start automatically. At this time, we need to dial the knob back to the parking position, in the dial back to the open position can start. You can pay attention to this.
在结束工作时░,一定要把活塞离开丁基胶░,要将胶缸置于退的位置░,在大约2至3秒后置于停。这很重要░,在未加热或未升温至设定温度时░,胶缸状态开关必须置于“停”░,否则会出现机械故障
At the end of the work, the piston must be removed from the butyl rubber, and the cylinder should be placed in the retreat position and stopped after about 2 to 3 seconds. It is very important that the cylinder state switch must be put on "stop" when it is not heated or heated to the set temperature, otherwise mechanical failure will occur.
一般中空玻璃打胶机胶缸温度设定在110~120℃░,胶头温度设定在120~140℃░,就能正常工作░,但░,由于各丁基胶生产厂家配料比例•●、价格工艺不同░,生产出的丁基胶的热熔温度也不同░,所以░,在使用不同厂家的丁基胶时░,先手动试打胶░,打出的胶太稀░,降低设定温度░,若不出胶或不粘;则升高设定温度。
Generally, the cylinder temperature of hollow glass glue beater is set at 110-120 C, and the head temperature is set at 120-140 C, which can work normally. However, due to the different proportions and price processes of butyl rubber manufacturers, the hot melting temperature of butyl rubber produced is also different. Therefore, when using butyl rubber from different manufacturers, the glue produced is too thin and the setting temperature is lowered. If no glue or no glue is produced, the setting temperature will be raised.

全自动封胶机
调试的注意事项:
Notes for debugging:
1•●、在当天机器操作完毕后要把胶管内的胶冲出░,防止硬化;如果长时间不实用要注意用煤油清洗胶管和胶枪。
1. After the machine is finished, the glue in the rubber tube should be washed out to prevent hardening. If it is not practical for a long time, we should pay attention to cleaning the rubber tube and gun with kerosene.
2•●、双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高░,低质量的胶容易堵塞胶管的过滤系统░,造成出胶不畅或不均匀。
2. Silicone glue or polysulfide glue used in two-component glue beater should pay attention to the impurities should not be too high, low-quality glue is easy to block the filter system of rubber hose, resulting in poor or uneven glue production.
3•●、在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净░,最好清洗░,因为不同品种甚至品牌的胶容易反应堵塞机器。
3. When changing the type of glue, special attention should be paid to rinsing the residual glue in the two-component glue beater, and it is better to clean it, because the glue of different varieties or even brands can easily react to clogging the machine.
4•●、液压站系统的压力░,不能调的太高░,要根据室内环境温度等实际情况░,调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪░,否则B组份管路压力将升得很高░,造成安全事故。
4. The pressure of hydraulic station system can not be adjusted too high. According to the actual situation of indoor environment temperature, it can be adjusted to meet the normal tapping of rubber nozzles. When opening the hydraulic station, the rubber gun must be opened, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
本章由全自动封胶机给大家介绍的内容就暂且到这里░,希望我们的解答能够帮助到您░,如果您对此还有疑问░,详情请咨询我们的官方。
The content of this chapter introduced by automatic sealing machine is here for the time being. I hope our answers can help you. If you have any questions about this, please consult our official for details.

www.kecimusic.com
友情链接:诺亚彩票  亦博彩票  四柱彩票  全球彩票  博发彩票  同乐彩  地球人彩票  好彩投彩票  富赢彩票  百盛彩票  平安彩票  168彩票  好博彩票  葡京彩票  头彩网  众合彩票  国彩彩票  8888彩票  彩票8  58彩票网