清洗胶机的涂胶系统应注意截流阀关闭

发布时间:2018/01/30    发布人:

  当胶流速变慢或者混胶不均时清洗混合器。将混合器拆下横放在台钳上░,夹住两端盖░,不要夹到螺丝。用六角扳手松开两端的六条螺丝░,打开器体░,取出垫片░,挡针░,混合芯。将各个零件清洗干净。
  The mixer is cleaned when the flow rate is slow or the glue is uneven. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Release the six screws at both ends with a six angle wrench, open the body, remove the gasket, the needle, and the mixed core. Clean the parts.
  端盖不要弄变形░,各个平面不要有划伤。混合器一端有凹槽░,安装时将其放进有挡针孔的一面░,将挡针放入挡针孔░,横放在凹槽上。
  Do not deform the cover, and do not have any scratches in each plane. The mixer end is provided with a groove, the installation will be put into the side of retaining the pinhole, will stop into the retaining needle pinhole, across the groove.
  更换好垫片后将端盖对准器体░,A对A░,P对P░,拧上螺丝░,拧好后横放在台钳上夹紧░,用扳手拧紧下端的四条螺丝░,松开台钳░,器体旋转300°░,夹紧台钳░,再拧紧下面四条螺丝。依次拧四五次即可。按A面进口░,P面出口安装到胶机上即可。

双组份打胶机
  Replace gasket after the end cap aligner, A to A, P to P, screw, screw after lying in a vise clamped by four screws, the lower end of the wrench to tighten loose vise device body is rotated 300 degrees, and then tighten the clamping vise below four screws.  Turn four or five times in turn. According to the A surface, the P surface is installed on the glue machine.
  枪口混合器清洗时直接拧下枪口混合器取出混合芯即可。清洗枪柄混合器时░,先把枪上的定位螺丝松开░,然后拧下枪柄混合器。枪口混合器同混合器同周期清洗;抢柄混合器同枪同周期清洗░,半年或一年洗一次。
  When the muzzle mixer is cleaned, the muzzle mixer is directly unscrewed out and the mixed core is removed. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer. The muzzle mixer is cleaned in the same cycle with the mixer; the shank mixer is cleaned with the gun in the same cycle, and is washed once in half a year or a year.
  清洗时将其拧下░,用尖嘴钳拧下小螺母░,拔出针体░,弹簧。全部清洗干净。针阀出口平面及针帽确保无任何杂质░,划伤░,变形。安装时将针插入阀体░,弹簧套在针体上░,螺母大头向里面拧紧░,力量在1到2公斤左右。
  When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean up all. Needle valve outlet plane and needle cap to ensure no impurities, scratch, deion.  When installed, the needle is inserted into the body. The spring is set on the body of the needle and the nut head is tightened to the inside. The force is about 1 to 2 kilograms.
  将两个桶都放在机器上░,并处于正常工作时的状态░,清洗胶机的涂胶系统(混合器░,针阀░,枪口░,枪柄混合器)。清洗后安装好░,注意截流阀关闭。再用的时候清洗Y型过滤网░,大过滤网即可。
  Two barrels are placed on the machine, and in a normal working state, glue system cleaning glue machine (mixer, needle, gun muzzle, mixer). After cleaning, pay attention to the closure of the closure valve. Use the time to clean Y filter network, large filter network.
  本文由双组份打胶机为您提供░,我们的网站是:我们将以全心全意的热情为您提供更优质的服务░,欢迎您的访问!
  This article is provided by two component glue machine. Our website is: , we will provide you with better service with wholehearted enthusiasm, welcome your visit.

www.kecimusic.com
友情链接:喜盈门彩票  大运彩票  pp彩票  91彩票  彩拾彩票  917彩票  彩票2元网  利威彩票  优乐彩  地球人彩票  头彩网  彩29彩票  49彩票  顺盈彩票  平安彩票  龙头彩票  58彩票网  宝博彩票  汇盈彩票  80彩票