胶流速变慢八成是这里的原因

发布时间:2017/12/26    发布人:

  打胶机胶枪的枪口混合器清洗时直接拧下枪口混合器取出混合芯即可。清洗枪柄混合器时░,先把枪上的定位螺丝松开░,然后拧下枪柄混合器。枪口混合器同混合器同周期清洗;抢柄混合器同枪同周期清洗░,半年或一年洗一次。
  The mixing core of the muzzle mixer is directly unscrewed out when the muzzle mixer of the glue machine glue gun is cleaned. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer. The muzzle mixer is cleaned in the same cycle with the mixer; the shank mixer is cleaned with the gun in the same cycle, and is washed once in half a year or a year.
  打胶机大过滤器的位置在高压表B表右下░,拧下回流阀下方胶管░,拧下过滤器░,将网及网芯取出░,弹簧•●、取出░,刷干净░,将弹簧小孔套在网芯的凸点上。倒着装入器体后转过来拧在胶机上。用3-5组洗一次░,如无杂质░,灵活掌握即可 。
  The location of the large filter of the rubber beating machine is under the bottom of the B table of the high-voltage meter, unscrewing the rubber hose under the reflux valve, unscrewing the filter, taking the net and the net core out, and spring, removing and cleaning it, and putting the spring hole on the bump of the net core. Reverse the loader body and turn it on the glue machine. Use 3-5 groups of washing, such as no impurities, flexible mastery.

双组份打胶机多少钱
  当胶流速变慢或者混胶不均时清洗混合器。将混合器拆下横放在台钳上░,夹住两端盖░,不要夹到螺丝。用六角扳手松开两端的六条螺丝░,打开器体░,取出垫片░,挡针░,混合芯。将各个零件清洗干净。端盖不要弄变形░,各个平面不要有划伤。
  The mixer is cleaned when the flow rate is slow or the glue is uneven. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Release the six screws at both ends with a six angle wrench, open the body, remove the gasket, the needle, and the mixed core. Clean the parts. Do not deform the cover, and do not have any scratches in each plane.
  混合器一端有凹槽░,安装时将其放进有挡针孔的一面░,将挡针放入挡针孔░,横放在凹槽上。更换好垫片后将端盖对准器体░,A对A░,P对P░,拧上螺丝░,拧好后横放在台钳上夹紧░,用扳手拧紧下端的四条螺丝░,松开台钳░,器体旋转300°░,夹紧台钳░,再拧紧下面四条螺丝。依次拧四五次即可。按A面进口░,P面出口安装到胶机上即可。
  The mixer end is provided with a groove, the installation will be put into the side of retaining the pinhole, will stop into the retaining needle pinhole, across the groove. Replace gasket after the end cap aligner, A to A, P to P, screw, screw after lying in a vise clamped by four screws, the lower end of the wrench to tighten loose vise device body is rotated 300 degrees, and then tighten the clamping vise below four screws. Turn four or five times in turn. According to the A surface, the P surface is installed on the glue machine.
  清洗时将其拧下░,用尖嘴钳拧下小螺母░,拔出针体░,弹簧。全部清洗干净。针阀出口平面及针帽确保无任何杂质░,划伤░,变形。安装时将针插入阀体░,弹簧套在针体上░,螺母大头向里面拧紧░,力量在1到2公斤左右。
  When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean up all. Needle valve outlet plane and needle cap to ensure no impurities, scratch, deion. When installed, the needle is inserted into the body. The spring is set on the body of the needle and the nut head is tightened to the inside. The force is about 1 to 2 kilograms.
  打胶机Y型过滤器的位置在辅料泵出口处░,清洗时将端盖拧下░,用煤油浸泡░,用牙刷类刷子刷干净。安装时将网放在端盖里用手拧到底░,再用扳手拧紧。用一组胶洗一次░,如无杂质两组胶洗一次░,灵活掌握。
  The position of the Y filter is at the exit of the auxiliary pump. When cleaning, the end cover is screwed down, the oil is soaked with kerosene, and the brush type brush is used. The installation will be placed on the end cover by hand net screwed in the end wrench, tighten. Use a group of glue to wash once, such as no impurity two groups of glue washing once, flexible mastery.
  本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站: 谢谢您的到来!
  The wonderful content of this article comes from the detailed content of the double component glue machine, please click on our official website: thank you for your arrival!

www.kecimusic.com
友情链接:正点彩票  春秋彩票  人人发彩票  好运彩票  壹乐多彩票  博金冠彩票  520彩票  GT彩票  博发彩票  彩66彩票  美娱彩票  博易彩票  七匹狼彩票  百胜彩票  购乐彩票  彩票2元网  时时彩票  必威彩票  新凤凰彩票  868彩票