混合胶沉积会影响正常的出胶量

发布时间:2017/11/28    发布人:

  1•●、压盘上的放气阀门要保持通畅░,要定期疏通和清洗。

  1, the vent valve on the press plate should be kept smooth, and should be regularly dredged and cleaned.

  2•●、正常工作时不要断气源░,如果发现断气源应停止工作。

  Don't cut off the gas source, 2 normal work, if it is found that asgassource should stop working.

  3•●、若涂胶工作过程中停顿时间超过15分钟以上时░,一定要用“冲枪”。本机有报警功能░,到时没有冲胶会有蜂鸣器报警。

  3. If the pause time is more than 15 minutes in the process of gumming, the "gun" must be used. This machine has an alarm function, and there will be a buzzer with no punching glue at the time.

  4•●、定期检查气源░,首先应保证使用经干燥的洁净压缩空气░,并定期排放分离过滤器中的积水░,检查油雾器中的油是否够用。

  4, regular inspection of gas source, first of all, we should ensure the use of dry clean compressed air, and regularly discharge the water in the separation filter, check whether the oil in the oil mist is enough.

  5•●、硅酮胶B 组份遇空气会结壳░,影响泵的正常工作和管路的畅通░,因此░,停机时B组份胶的所有通道在泄压后均应关闭░,使B组份不得接触空气。

  5, silicone rubber B components will be crusted in air, which will affect the normal operation of pumps and the smooth flow of pipes. Therefore, all channels of B components should be shut down after depressurization, so that B components must not touch air.

双组份打胶机多少钱

  6•●、B胶桶内如果要有空气░,空气将排不出来░,B泵将快速往返运动░,不能向高压泵内正常供胶░,影响整个系统░,因此░,必须将空气排出来。方法是:将压盘提出从新压入并放气。

  6, if there is air in the B barrel, the air will not be discharged. The B pump will move back and forth quickly, and it can not supply glue to the high-pressure pump, which will affect the whole system. Therefore, the air must be drained out. The method is to put the pressure plate into the new pressure and deflate.

  7•●、液压站系统的压力░,不能调的太高░,要根据室内环境温度等实际情况░,调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪░,否则B组份管路压力将升得很高░,造成安全事故。

  7, hydraulic station system pressure, can not be adjusted too high, according to the indoor environment temperature and other actual conditions, to meet the glue mouth normal glue can be evenly glued. When the hydraulic station is opened, the glue gun must be opened, otherwise the pressure of the B components will rise very high, causing a safety accident.

  8•●、A胶提胶泵连续工作1分钟以上没有供胶停止░,说明管路内有空气░,此时会报警░,须打开泵上管接头再打开A胶提胶泵░,直到出胶为止░,停止并接好接头░,胶枪会出现有空气的哔哔爆破声░,空气排净就好了。

  8, A glue gel extraction pump work for more than 1 minutes without glue stop, that air is in the pipeline, the alarm will have to open the pump pipe joint, then open the A glue rubber glue pump, until now, stop and connect the connector glue gun will appear beep sound blasting with air. The air net is good.

  9•●、由于每次冲洗混合器不会完全干净░,每次都有少量的混合胶沉积░,越来越多░,以致堵塞混合器通道░,用一段时间后░,影响出胶量和混合效果░,因此要定期(聚硫胶五天░,硅酮胶两天)清洗混合器。把混合器内的混胶棒拆出░,如有损坏更换新的混胶棒。若混胶棒拆不出来░,可用火烧掉░,注意不能损伤零件螺纹。

  9, because every flush mixer will not completely clean, every time there is a small amount of glue mixed deposits, more and more, that blocking the channel mixer, after a period of time, influence the quantity of cement and mixing effect, so regular (five days of polysulfide rubber, silicone rubber mixer cleaning for two days). The glue mixer and mixing, the damage as the replacement of the rubber mixing rod. If the glue stick can't be removed, the fire can be burnt out, and the thread of the part can not be damaged.

  本文的精彩内容来自双组份打胶机详细内容请点击我们的官方网站:谢谢您的到来!

  The wonderful content of this article comes from the detailed content of the double component glue machine, please click on our official website: thank you for your arrival!

www.kecimusic.com
友情链接:彩都会彩票  九五彩票  新华彩票  868彩票  开门彩  长江彩票  178彩票网  4u彩票  YY彩票  大奖网彩票  博雅彩  喜盈门彩票  520彩票  壹玖玖彩票  百胜彩票  大运彩票  正点彩票  七匹狼彩票  361彩票  九龙彩票